The Driller
  • Sign In
  • Create Account
  • Sign Out
  • My Account
  • NEWS
  • CLASSIFIEDS
  • EQUIPMENT
  • SAFETY
  • VIDEOS
  • EDUCATION
  • SOURCEBOOK
  • EVENTS
  • SUBMIT
  • ABOUT
  • SIGN UP
cart
facebook twitter linkedin youtube
  • NEWS
  • Water
  • Geothermal
  • Construction
  • Environmental
  • Mining
  • All Industry News
  • EQUIPMENT
  • Rigs & Heavy Equipment
  • Consumables
  • Pumps
  • Featured Products
  • VIDEOS
  • Newscast
  • Drill Talks
  • Ask Brock
  • Emerging Drillers
  • EDUCATION
  • Drilling Business Insights
  • Reference Desk
  • Sponsored Insights
  • EVENTS
  • Conferences & Demo Days
  • Newscast LIVE
  • SUBMIT
  • Drillers @Work
  • ABOUT
  • Contact
  • Advertise
The Driller
search
cart
facebook twitter linkedin youtube
  • Sign In
  • Create Account
  • Sign Out
  • My Account
The Driller
  • NEWS
    • Water
    • Geothermal
    • Construction
    • Environmental
    • Mining
    • All Industry News
  • CLASSIFIEDS
  • EQUIPMENT
    • Rigs & Heavy Equipment
    • Consumables
    • Pumps
    • Featured Products
  • SAFETY
  • VIDEOS
    • Newscast
    • Drill Talks
    • Ask Brock
    • Emerging Drillers
  • EDUCATION
    • Drilling Business Insights
    • Reference Desk
    • Sponsored Insights
  • SOURCEBOOK
  • EVENTS
    • Conferences & Demo Days
    • Newscast LIVE
  • SUBMIT
    • Drillers @Work
  • ABOUT
    • Contact
    • Advertise
  • SIGN UP
MarketsOpinionsWater Wells

Tech Topics: How to Calculate and Control Pressure-tank Drawdown

By Bob Pelikan
August 1, 2011
Factoring drawdown in conventional tanks.

Last month, we said that the term “drawdown” refers to the amount of useable water that can be drawn from a hydropneumatic tank from the time the pressure switch cuts out, turning off the pump, until the pressure switch cut back in, turning the pump back on. The amount of drawdown capacity is determined by a formula known as Boyle’s Law. Simply put, Boyle’s Law states as the volume of the air cushion in a tank decreases, the pressure of that air cushion increases. Conversely, as the volume of the air cushion increases, the pressure of that air decreases. Therefore, for any given tank, drawdown equals the volume of air at cut-in minus the volume of air at cut-out. Stated as a mathematical formula, taking into consideration the total volume of a pressure tank, it looks like this:

Drawdown = P1V / P2 – P1V / P3 where,

P1 is the pre-charge pressure.

P2 is the cut-in pressure.

P3 is the cut-out pressure.

V is the total tank volume.

Remember that all pressures must be stated in terms of absolute pressure. At sea level, add 14.7 psi to the gauge pressure to get absolute pressure. To make the calculations easier, Boyle’s Law can be restated as:

Drawdown = (P1 / P2 – P1 / P3) x V

Let’s try a couple of examples.


Example 1

30/50 pressure switch.

P1, the pre-charge pressure, is 28 psi.

P2, the cut-in pressure, is 30 psi.

P3, the cut-out pressure, is 50 psi.

V, the total tank volume, is 85 gallons.

Altitude is sea level.

The drawdown formula then looks like this:

Drawdown = (28 + 14.7) divided by (30 + 14.7) minus (28 + 14.7) divided by

(50 + 14.7) times 85. Or, (42.7 / 44.7) – (42.7 / 64.7) x 85

Therefore, drawdown = 0.295 x 85 = 25.1 gallons.



Example 2

Use the same tank conditions, but put the job up at Lake Tahoe in California at 6,000 feet above sea level, where the atmospheric pressure is 11.8 psi, instead of 14.7 psi.

This time, drawdown = (28 + 11.8) / (30 + 11.8) – (28 + 11.8) / (50 + 11.8) x 85

Now, drawdown = 0.307 x 85 = 26.1 gallons.



Example 3

Imagine a 30/50 pressure switch, but no pre-charge, as could be the case with a conventional tank with no pre-charge.

Drawdown = (0 + 14.7) / (30 + 14.7) – (0 + 14.7) / (50 + 14.7) x 85

Drawdown = 0.102 x 85 = 8.7 gallons, about 10 percent of the total tank capacity. As we will point out later, it is possible – though not always standard practice – to pre-charge conventional tanks.



Example 4

Instead of a 30/50 pressure switch, use a 40/60 pressure switch with a 38-psi pre-charge, and the numbers look like this:

Drawdown = (38 + 14.7) divided by (40 + 14.7) minus (38 + 14.7) divided by (60 + 14.7) x 85.

Therefore drawdown = 25.8 x 85 = 21.9 gallons.



Example 5

Consider how the drawdown changes if we widened the differential between the cut-in and cut-out pressures from 30/50 to 30/60.

Drawdown = (28 + 14.7) / (30 + 14.7) – (28 + 14.7) / (60 + 14.7) x 85

Drawdown = 38.4 x 85 = 32.6 gallons.

Compare this with the 25.1 from Example 1. A word of caution: Before expanding the cut-in/cut-out differential beyond 20 psi, check with your tank manufacturer to make sure that by doing so, you will not be over-expanding the water chamber.

Another term used in determining drawdown is “acceptance factor.” This simply is the factor by which you multiply the total tank volume to get drawdown.

In other words, drawdown = acceptance factor x total tank volume.

If you would rather work with acceptance factors, take the “V” out of the Boyle’s Law formula, and it becomes: Acceptance factor = P1/ P2 – P1/ P3.

Taking it one step further, if you consider the pre-charge to be the same as the pump cut-in pressure, P1/ P2 becomes 1, and the formula then is: Acceptance factor = 1 - P1/ P3.

However, as pointed out in earlier articles, the pre-charge must be set a minimum of 2 psi below the pump cut-in pressure to avoid the possibility of having the system pressure drop abruptly to zero before the pump turns on. It is imperative in a captive-air tank to have the pre-charge set at least 2 psi below the pump cut-in pressure. I strongly recommend using the proper version of Boyle’s Law, which includes a separate factor for pre-charge in order to accurately represent the drawdown of your system. And remember always to work in terms of absolute pressure in your Boyle’s law calculations by adding atmospheric pressure (14.7 at sea level) to the gauge pressure.


Conventional Pressure Tanks: Controlling Drawdown

For a conventional tank to have the same drawdown ratio as a captive-air tank, it is necessary to pre-charge the conventional tank, and to maintain the same air/water ratio as would be the case in a captive-air tank (see Figure 1 on p. 40). Logic states that if you have the same amount of air available to push the water out, you will be able to deliver the same amount of water between pump cycles, regardless of whether or not the tank has a diaphragm separating the air from the water. In a captive-air tank, the diaphragm assembly virtually is out of water when the pump turns on. To get the same performance from a conventional tank, the water level can be set such that the pump turns on just before the water level drops to the level of the inlet/outlet fitting.

In large conventional tanks (see Figure 2), the easiest method of optimizing the drawdown is to use a small air compressor in conjunction with a water-level probe. The advantage of this set-up is that the probe level can be set anywhere in the tank – from the top to the bottom – to optimize the drawdown. Used with a 30/50 pressure switch, the probe should be set at one-third the distance from the water outlet to the top of the tank. For low-pressure switch settings like 20/40, the probe will be set a little higher, and for high-pressure switch settings like 40/60, the probe will be a little lower.

There are two such compressor units commercially available on the market today – the Charge-air 2000 from Maass Midwest (800-323-6259) and the Air Rite by Whitewater Manufacturing (800-966-3110).

Compressor/probe air charging systems typically are used on larger conventional tanks for economic reasons, but you often will see them on smaller tanks where optimizing the drawdown is necessary due to space limitations. Next month, we will talk about other air-charging techniques commonly used with smaller conventional tanks. ’Til then….
KEYWORDS: water well tanks

Share This Story

Looking for a reprint of this article?
From high-res PDFs to custom plaques, order your copy today!

Bob is a regular contributor to The Driller. Contact bobpelikan@comcast.net to request a copy of The Pump Book, a compilation of Bob's columns for reference or training available for only $20.

Recommended Content

JOIN TODAY
to unlock your recommendations.

Already have an account? Sign In

  • geotechnical drilling rig

    6 Onsite Phrases Environmental Drillers Hate

    Here are six phrases that highlight common frustrations...
    Environmental Monitoring
    By: Jeff Garby
  • Wayne Nash

    Pipe Stuck? Common Causes and Solutions for Drillers

    If you have drilled for any length of time, sooner or...
    Markets
    By: Wayne Nash
  • submersible pumps, water well pumps

    Selecting and Sizing Submersible Pump Cable

    This article helps pump installers and servicers decide...
    Pumps
    By: Bob Pelikan
You must login or register in order to post a comment.

Report Abusive Comment

Subscribe For Free!
  • eNewsletters
  • Online Registration
  • Subscription Customer Service
  • Manage My Preferences

The Driller Newscast, Episode 147: Global Geothermal Collaboration at NY-GEO 2025

The Driller Newscast, Episode 147: Global Geothermal Collaboration at NY-GEO 2025

The Driller Newscast: 21st Century Drillers | Part 1 DEMAND

The Driller Newscast: 21st Century Drillers | Part 1 DEMAND

The Driller Newscast: New York Geo Talks 2025 Conference with Hands-on Driller Education

The Driller Newscast: New York Geo Talks 2025 Conference with Hands-on Driller Education

The Driller Newscast: Coiled Tubing Drilling and the Future of Geothermal

The Driller Newscast: Coiled Tubing Drilling and the Future of Geothermal

More Videos

Sponsored Content

Sponsored Content is a special paid section where industry companies provide high quality, objective, non-commercial content around topics of interest to the The Driller audience. All Sponsored Content is supplied by the advertising company and any opinions expressed in this article are those of the author and not necessarily reflect the views of The Driller or its parent company, BNP Media. Interested in participating in our Sponsored Content section? Contact your local rep!

close
  • demo of a DM450 drilling rig during a customer factory visit
    Sponsored byGeoprobe

    Built for You: Smarter Drill Rigs, Stronger Support, Bigger Opportunities

Popular Stories

MainPhotoTwoBrothers.jpg

Two Brothers' Journey Through the Drilling Industry

Tariffs

Tariffs Shake Up the Drilling Industry

AI and Drought Concerns

AI’s Growing Thirst for Water and Power

The Driller Classifieds

COMPRESSORS

EAST WEST MACHINERY & DRILLING IS BUYING AND SELLING AIR COMPRESSORS, AIR BOOSTERS, AIR ENDS & PARTS
Company: East West Machinery

DRILL RIGS

LOOKING FOR LATE MODEL TOPHEADS & DRILLTECH D25'S
Company: Spikes’s Rig Sales

DRILL RIG PARTS

MEETING DRILLERS NEEDS AROUND THE WORLD
Company: East West Machinery

ELEVATORS

SEMCO INC. PIPE ELEVATORS
Company: Semco Inc.

GROUTERS

GROUTING EQUIPMENT - GROUT PUMPS & GROUT HOSE REELS
Company: Geo-Loop Inc.

PUMP HOISTS

SEMCO INC. - BASIC PUMP HOISTS
Company: Semco Inc.

WELL PACKERS

LANSAS PRODUCTS - INFLATABLE WELL PACKERS
Company: Vanderlans Lansas Products

WELL SCREENS

WELL SCREENS & SLOTTED PIPE
Company: Alloy Screen Works

Products

Water Quality Engineering: Physical / Chemical Treatment Processes

Water Quality Engineering: Physical / Chemical Treatment Processes

By carefully explaining both the underlying theory and the underlying mathematics, this text enables readers to fully grasp the fundamentals of physical and chemical treatment processes for water and wastewater.

See More Products

Subscribe to The Driller Newscast

Related Articles

  • How to Calculate and Control Pressure Tank Drawdown

    See More
  • Tech Topics: How to Calculate Pressure Drop Due to Friction in a Piping System - Part 2

    See More
  • Tech Topics: How to Calculate Pressure Drop - Part 2

    See More

Related Products

See More Products
  • M:\General Shared\__AEC Store Katie Z\AEC Store\Images\ND\new site\water-well-pumps.gif

    Audel Water Well Pumps and Systems Mini-Ref

  • M:\General Shared\__AEC Store Katie Z\AEC Store\Images\ND\new site\water-quality-eng.gif

    Water Quality Engineering: Physical / Chemical Treatment Processes

  • M:\General Shared\__AEC Store Katie Z\AEC Store\Images\ND\new site\modern-well-design.gif

    Modern Well Design: Second Edition

See More Products
×

Dig deeper into the drilling and water supply industry!

Build your knowledge with The Driller, covering the people, equipment and technologies across drilling markets.

SIGN UP NOW
  • RESOURCES
    • Advertise
    • Contact Us
    • Directories
    • Store
    • Want More
    • Classifieds
  • SIGN UP TODAY
    • Create Account
    • eNewsletters
    • Customer Service
    • Manage Preferences
  • SERVICES
    • Marketing Services
    • Reprints
    • Market Research
    • List Rental
    • Survey/Respondent Access
  • STAY CONNECTED
    • LinkedIn
    • Facebook
    • YouTube
    • X (Twitter)
  • PRIVACY
    • PRIVACY POLICY
    • TERMS & CONDITIONS
    • DO NOT SELL MY PERSONAL INFORMATION
    • PRIVACY REQUEST
    • ACCESSIBILITY

Copyright ©2025. All Rights Reserved BNP Media.

Design, CMS, Hosting & Web Development :: ePublishing

The Driller
search
cart
facebook twitter linkedin youtube
  • Sign In
  • Create Account
  • Sign Out
  • My Account
The Driller
  • NEWS
    • Water
    • Geothermal
    • Construction
    • Environmental
    • Mining
    • All Industry News
  • CLASSIFIEDS
  • EQUIPMENT
    • Rigs & Heavy Equipment
    • Consumables
    • Pumps
    • Featured Products
  • SAFETY
  • VIDEOS
    • Newscast
    • Drill Talks
    • Ask Brock
    • Emerging Drillers
  • EDUCATION
    • Drilling Business Insights
    • Reference Desk
    • Sponsored Insights
  • SOURCEBOOK
  • EVENTS
    • Conferences & Demo Days
    • Newscast LIVE
  • SUBMIT
    • Drillers @Work
  • ABOUT
    • Contact
    • Advertise
  • SIGN UP